OPERATOR’S MANUAL PLEASE READ THIS MANUAL CAREFULLY AND KEEP READY AT ALL TIMES KUBOTA® BRUSH MOWER MODEL K4080
BASIC OPERATION BASIC OPERATION 8 1. Before beginning your job, walk the mowing area and clear all hidden hazards such as large rocks, stumps, utilit
BASIC OPERATION Starting Procedure 1. While the excavator’s engine is turned OFF, and all moving parts have completely stopped, remove outer spindle c
MAINTENANCE MAINTENANCE 10 ATTENTION Before doing any service work, observe the following safety rules: 1. Remove the ignition key from the operating
REPLACING KNIVES REPLACING KNIVES 11 1. Worn knives, bolts, and spacers must be replaced. Neglecting the replacement of these parts could cause the c
HYDRAULIC DIAGRAM HYDRAULIC DIAGRAM 12 The diagram below represents the hydraulic plumbing system for the Kubota K4080 Brush Mower attachment. To reve
TRANSPORT TRANSPORT 13 ATTENTION Allow all movements to stop before leaving the operator’s position to lubricate or clean the machine. Before workin
T. Where is the serial number for my machine? C. The serial number for your brush shredder is stamped next to the mounting bracket on the opposite si
T. How do I reverse the cutter drum rotation? C. Refer to the Adjustments and Maintenance section of this manual for information on reversing the hy
K4080 Brush Mower Specifications SPECIFICATIONS SPECIFICATIONS 16 Working Width 40” (101.6 cm) Overall Width 58” (127 cm) Weight 1,32
KNIFE ASSEMBLY # Description Model Part # Quantity 1 2 3 4 5 6 7 BOLT, KNIFE 1"x4" GR8 -2 1/2" Shoulder KNIFE, SHREDDER SPACER, 1&quo
BEFORE OPERATION ——————————————————————— 1 SAFE OPERATION —-——————————————————————— 2-3 ATTACHING TO THE EXCAVATOR —-———————————————— 4-5 ADJUSTMEN
DRIVE ASSEMBLY # Description Model Part # Quantity 1 2 3 4 5 6 7 8 9 10 11 12 GUARD, WIRE - DRIVE SIDE SEAL, SHAFT 3 1/2"x2 3/4" OD WASHE
HYDRAULIC PLUMBING # Description Model Part # Quantity 1 2 2a 2b 3 4 5 6 7 Hydraulic Motor-24 GPM Motor Protection Valve MPV Pressure Relief MPV C
NOTES Notes 20
K4080 Complete Parts List Qty. Per Unit Description Part Number 1 BEARING, FLANGE (1 15/16" 4 BOLT) 77700-00852 24
PRINTED IN USA KUBOTA TRACTOR CORPORATION 3401 Del Amo Blvd., Torrance, CA 90503, U.S.A. Telephone: (310) 370-3370 Western D
BEFORE OPERATION 1 BEFORE OPERATION 1. Keep children out of the operating area under the watchful eye of another re-sponsible adult. 2. Never allo
SAFE OPERATION 2 SAFETY Failure to heed these warnings may result in personal injury or death. • Before operating this machinery read the owner’s m
SAFE OPERATION 3 • Stop the operation of this machine when people or vehicle driver’s vision becomes obscured, caused by the discharge of materials
ATTACHING TO THE EXCAVATOR • Be sure to inspect all safety devices (including safety shields, guards, deflectors, etc.) before each use. Safety Dev
ATTACHING TO THE KX080 ATTENTION The K4080 brush mower is designed specifically for the Kubota KX080 excavator and should not be used on any other mac
ADJUSTMENT & MAINTENANCE CLEANING YOUR BRUSH MOWER To preserve life of paint and decals, wash the brush mower after each use. The preservation of
Running Your Attachment The K4080 brush mower is designed to cut all types of vegetation such as grass, brush and small trees. The condition of your
Kommentare zu diesen Handbüchern